Parts & Accessories

Whisky Parts Co. Tubeless Rim Tape.

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

- Shell: 8mm flanged axle nut - Flanged

- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually

Grade 10 chromium steel balls

Secure - Prevents theft instead of standard 9 mm quick-release skewers Quick Assembly - Use proprietary key on frame dropout Construction - Stainless springs with chromoly axle

The square bottom on the rubber, plus the rubber extending down the valve helps create the best airtight sealing system. Set up is a breeze and works much better than other valves on the market. - 44mm valve for 28mm carbon, Altamont, Altamont, CCC, and MTB wheels - 60mm valve for 44mm carbon and 36mm depths (36 Road Disc, Pinnacle, and Jocassee) - 80mm valve for 55 Road Disc and 60mm carbon - 110mm valve for 90mm carbon and 90 Road Disc - Weights for the valve (with nut for tightening) is: 44mm—5g, 55mm—5g, 60mm—6g, 80mm—6g, 110mm—8g

Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

Includes rim strip and tubeless tape for 1 wheel.

- Wheel bearing kit front/rear - Bearing dimensions: 17 x 30 x 7mm - Material: steel - 2 pieces

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

- Kits include Freehub body with CeramicSpeed bearings pre-installed for easy installation onto the wheel - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings

- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed

Freehub bodies for Zipp Cognition hubs.

- Freehub for Cognition V2 hubs

- Freehub for Cognition V2 hubs

Zipp Speed Weaponry Rear Axle Conversion Kit - Not to be used on 188 V6 or earlier rear hubs - Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

A simple solution for completing the Zipp aerodynamic package by covering the valve access hole on most disc wheels. Black, self-adhesive oval patches with the Z logo, in a package of five.

Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1) Compatible With: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1

Wheel Freehub Kit—XD Driver Body Kit—Zipp ZM2 - Compatible With: WH-MOTO-30-B1

Wheel Freehub Kit SS 176/177 SRAM XDR - End Caps Not Included Compatible With: WH-202-CCR-A1, WH-202-TLD-A1, WH-202-TUD-A1, WH-302-CCD-A1, WH-302-CCR-A1, WH-302-TLR-A1, WH-303-CCR-B1, WH-303-TLD-A1, WH-303-TUD-B1, WH-303-TUR-B1, WH-30C-CLD-A1, WH-30C-CLR-A1, WH-404-CCR-A1, WH-404-CCR-B1, WH-404-TLD-A1, WH-808-CCR-B1, WH-808-TLD-A1, WH-SP9-CC30-A1, WH-SP9-CCD-A1, WH-SP9-CCR-A1, WH-SP9-TUD-A1

Wheel Freehub Kit SRAM XDR for Super 9RB - Compatible only with the Super 9 - Compatible With: WH-SP9-CCR-A1

Wheel Freehub Kit—XD Driver Body Kit—ZM1 3Zero - Compatible With: WH-MOTO-30-A1

Rear Wheel Axle for X0 hubs, including the following wheels: Rise 60 (B1), Roam 30, Roam 40, Rail 40, Rise XX, Roam 50, 60 B1 Compatible with part numbers: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1